Plumber's Essentials: Your Key to Installing a Bathtub
Plumber's Essentials: Your Key to Installing a Bathtub
Blog Article
The article author is making a few good points related to How to Install a Bathtub as a whole in this post following next.
Mounting a tub isn't specifically rocket science, yet it does require strong plumbing, woodworking, as well as occasionally, tiling abilities. Replacing an old bath tub with a new one is likewise a reasonably difficult job. If the old bathtub is easily obtainable, the job can relocate quickly; if you need to open up a wall to eliminate the old bathtub and place the brand-new bathtub, the task is much harder. In either case, the job is within a house handyman's abilities, although you will require a helper to move out the old tub as well as embeded in the brand-new one. See to it you have qualified on your own for the task and also are comfortable trying it. Rather than employing a professional to take control of a halfway-completed task, it is much better to consider utilizing one prior to you start. Opportunities are you may need a specialist plumber to make tube links.
This post will certainly help you install a new tub in your shower room if you have actually already bought a new bathtub and also do not require to transform the setup of your previous water supply pipelines.
Your devices and also product checklist ought to consist of the following:
Removing Old Taps
If you need to change old faucets with brand-new ones as a part of your installment, after that the first thing you need to do is disconnect the supply of water. After doing so, switch on the taps to drain pipes any type of water staying in the system. The procedure of eliminating the existing faucets can be quite problematic as a result of the restricted gain access to that is commonly the situation.
Make use of a basin wrench (crowsfoot spanner) or a tap tool to reverse the nut that links the supply pipelines to the taps. Have a cloth prepared for the continuing to be water that will certainly come from the pipes. Once the supply pipes have been removed, make use of the same tool to loosen the nut that holds the faucets onto the bath/basin. You will certainly need to quit the single faucets from turning throughout this process. As soon as the faucets have been removed, the holes in the bath/basin will have to be cleansed of any kind of old securing substance.
Before proceeding to fit the brand-new taps, compare the pipe links on the old taps to the new faucets. If the old taps are longer than the new faucets, after that a shank adapter is required for the new taps to fit.
Fitting New Taps
If the tails of the new taps are plastic, then you will certainly need a plastic adapter to prevent damage to the thread. One end of the connector fits on the plastic tail of the tap as well as the various other end provides a connection to the existent supply pipes.
If you require to fit a monobloc, after that you will certainly call for decreasing couplers, which attaches the 10mm pipeline of the monobloc to the typical 15mm supply pipeline.
Next off, place the tap in the installing hole in the bath/basin guaranteeing that the washing machines remain in place in between the tap and also the sink. Secure the tap in place with the manufacturer given backnut. Once the faucet is safely in place, the supply pipes can be linked to the tails of the faucets. The faucets can either be linked by using corrugated copper piping or with regular faucet connectors. The previous type needs to be linked to the faucet ends first, tightening only by hand. The supply pipes can later on be connected to the other end. Tighten both ends with a spanner after both ends have actually been linked.
Installing the Bath tub
Utilizing the two wooden boards under its feet, place the tub in the required setting. The wooden boards are useful in evenly spreading the weight of the tub over the area of the boards instead of concentrating all the weight onto four tiny points.
The next objective is to ensure that the bathtub is leveled all round. This can be attained by examining the level as well as adjusting the feet on the tub till the spirit level reads degree.
To install faucets, fit the bottom of the outermost versatile tap port to the ideal supply pipe by making a compression sign up with; after that do the exact same for the various other tap.
Activate the water as well as examine all joints as well as brand-new pipework for leaks and also tighten them if essential. Fill up the bath tub as well as additionally examine the overflow electrical outlet as well as the typical electrical outlet for leakages.
Lastly, repair the bathroom paneling as explained in the manufacturer's user's manual. Tiling as well as sealing around the bathtub needs to wait till the bath tub has actually been utilized at the very least when as this will resolve it into its final position.
Preparing for the Installation
To start with, the supporting frame supplied with the bath ought to be fitted (if needed) according to the maker's instructions. Next off, fit the taps or mixer to the tub. When suitable the tap block, it is necessary to see to it that if the faucet comes with a plastic washer, it is fitted between the bathroom and the faucets. On a plastic bathroom, it is likewise practical to fit a supporting plate under the taps unit to stop strain on the bathtub.
Fit the versatile faucet ports to the bottom of both faucets using 2 nuts and also olives (sometimes provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the outlet via the hole in the bathroom. Utilize the nut provided by the supplier to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the flexible overflow pipe to the overflow outlet. Afterwards, screw the pipe to the overflow face which ought to be fitted inside the bath. Make sure you use all of the provided washers.
Link the trap to the bottom of the waste outlet on the bathtub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Connect all-time low of the overflow tube in a comparable manner.The bath need to now prepare to be suited its final placement.
Tiling Around the Bathtub
In the area where the bathroom satisfies the tile, it is needed to secure the accompanies a silicone rubber caulking. This is very important as the installation can relocate sufficient to split a rigid seal, creating the water to pass through the wall between the bath and the tiling, resulting in problems with wetness and possible leakages to the ceiling listed below.
You can pick from a variety of coloured sealers to assimilate your fixtures and also fittings. They are sold in tubes as well as cartridges, as well as are capable of sealing spaces up to a width of 3mm (1/8 inch). If you have a bigger space to fill up, you can load it with spins of drenched paper or soft rope. Bear in mind to constantly fill the tub with water prior to securing, to enable the movement experienced when the tub remains in use. The sealant can crack fairly early if you do not think about this activity prior to sealing.
Alternatively, ceramic coving or quadrant ceramic tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to size, are also easily offered on the marketplace. It is recommended to fit the ceramic tiles utilizing water-resistant or waterproof sticky as well as cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Do you really like more info about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround? Try leaving a remark down below. We will be glad to see your thinking about this review. In hopes that you come back again before long. Please take the opportunity to promote this blog post if you enjoyed it. I am grateful for your time. Please come by our website back soon.
Plumbing woes? We help. Report this page